 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MODEL 5610 SERIES 2" Diameter Single Turn Wirewound Precision Potentiometer MODEL STYLES 2 5611 5613 ELECTRICAL 1/4" Shaft, 3/8" Bushing 1/4" Shaft, Servo Resistance Range, Ohms Standard Resistance Tolerance Minimum Practical Resistance Tolerance Independent Linearity Minimum Practical Independent Linearity Power Rating, Watts Dielectric Strength Insulation Resistance, Minimum Noise, Maximum Actual Electrical Travel Tap Tolerance End Voltage, Maximum ENVIRONMENTAL (MIL-R-12934) 15 to 80K 5% 1.0% 1.0%, <50 Ohms 0.5%, 50 Ohms 1.0%, <50 Ohms 0.5%, 50-499 Ohms 0.25%, 500-4,999 Ohms 0.1%, 5K Ohms 3.5 at 70C derating to 0 at 125C 1,000V rms 1,000 Megohms 100 Ohms 356 + 1 1 Linearity x Input Voltage Operating Temperature Range Temperature Cycling Shock, 6ms Sawtooth Vibration Moisture Resistance High Temperature Exposure Rotational Life Rotational Load Life Specifications subject to change without notice. Static: -65C to +125C Dynamic: -40C to +125C 5 cycles, -65C to +125C (10% R) 50G's (0.1ms discontinuity max.) 15G's, 10 to 2,000 Hz (5% R, 0.1ms discontinuity max.) Ten 24 hour cycles (3% R) 1,000 hours at 125C (5% R) 1 Mil. Shaft Rev. 1 mil. shaft rev. at rated wattage at 70C (5% R) 2-51 Model 5610 Series MECHANICAL Total Mechanical Travel Number of Gangs, Maximum Weight, Nominal Backlash, Maximum Shaft End Play, Maximum Shaft Runout, T.I.R., Maximum Pilot Diameter Runout, T.I.R., Maximum Lateral Runout, T.I.R., Maximum Shaft Radial Play, Maximum Starting Torque, Maximum (per gang) Running Torque, Maximum (per gang) OUTLINE DIMENSIONS (Inch/mm) 360 Continuous 4 3.7 oz. Single Gang 1.3 oz. Each Added Gang 1 .005" 5611 5613 .0005" .001" .002" .0015" .004" .006" .004" .002" 1.5 oz.-in. 0.8 oz.-in. 1.1 oz.-in. 0.6 oz.-in. Model 5611 Bushing Mount with Sleeve Bearing Mounting Surface .875.031 22.20.79 .375 9.53 Min. +.0000 -.0003 Dia. +0.000 6.342 -0.008 .2497 90 Max. CCW Clamp CW Ears Slider 1.250 R. Max. 31.75 "RS" .031 0.79 "L" 2.000.016 50.800.41 Dia. 1.375.016 Dia. 34.930.41 +.000 .062 -.010 +0.00 1.58 -0.25 .375.016 9.530.41 +.000 -.002 Dia. +0.00 10.3 -0.05 .406 Chamfer .016 Max. x 45 0.41 3/8 - 32 UNEF Thread Dim. "L" .905.020 22.90.51 1.4670.22 37.260.56 2.029.024 51.540.61 2.591.026 65.810.66 .531.016 R. 13.50.41 Locating Hole .129.005 .062.016 Dia. x Deep 3.280.13 1.580.41 Positioned as shown 5 Dim. "RS" No. of Cups 1.405 35.69 1.967 49.96 2.529 64.24 3.091 78.51 1 2 3 4 2-52 Model 5610 Series OUTLINE DIMENSIONS (Inch/mm) Model 5613 Servo Mount with Ball Bearing "RS" .031 0.79 "L" .50 12.7 Min. Mounting Surface .625.031 15.90.79 .010 R. Max 0.25 +.0000 -.0003 Dia. +.000 +0.000 1.875 6.342 -.001 -0.008 +0.00 47.63 -0.03 .2497 90 Max. Slider CCW Clamp CW Ears 1.250 R. Max. 31.75 2 2.000.016 Dia. 50.800.41 2.000.005 Dia. 50.800.13 1.875 Dia. Max. 47.63 .073 Min. 1.85 .062.005 1.580.13 .093.005 2.360.13 Chamfer .016 Max. x 45 0.41 Dim. "L" 1.020.015 25.910.38 1.5820.17 40.180.43 2.144.019 54.460.48 2.706.021 68.730.53 Dim. "RS" No. of Cups 1.520 38.61 2.082 52.88 2.644 67.16 3.206 81.43 1 2 3 4 METRIC CONVERSIONS 1 in. 1 oz. 25.4 mm 28.4 gm 1 oz.-in. 1 lb.-in. 0,007 N-m 0,113 N-m 2-53 Model Series 5610 STANDARD RESISTANCE VALUES, OHMS Total Resistance 1K 2K 5K 10K 20K 30K 50K Theoretical Resolution (% Nominal) 0.089 0.071 0.058 0.053 0.043 0.040 0.040 * Lower tempco available as a non-standard model (consult factory). Tempco of Wire *130 ppm/C *130 ppm/C 20 ppm/C 20 ppm/C 20 ppm/C 20 ppm/C 20 ppm/C SPECIAL FEATURES Center Tap Linearity Tape Rear Shaft Extension Flatted Shaft Slotted Shaft Shaft Lock (5611 only) Additional Gangs ORDERING INFORMATION CT LT RS FS SS SL 2G or 3G or 4G 5611 R 10K T2 L .50 XX Model Series Resistance Prefix Resistance Value Optional Special Feature Code Linearity Optional Non-Standard Tolerance CIRCUIT DIAGRAM NOTES (S) (CCW) (CW) Metric equivalents, based on 1 inch = 25.4mm are rounded to the same number of significant figures as in the original English units and are provided for general information only. Tolerances unless otherwise specified: Linear = .01 inches (.25mm) Angular = 2 degrees INCH mm 2-54 Model 5610 Series |
Price & Availability of 5610
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |